- All Products
- Shop by Brands
- BW Technologies
- BW Technologies
- BW Technologies Monitors
- Models
- BW Clip
- BW Clip4
- GasAlertClip Extreme
- GasAlert Extreme
- GasAlertMicroClip XT
- GasAlertMicroClip XL
- GasAlertMicroClip X3
- GasAlertQuattro
- GasAlertMax XT II
- GasAlertMicro 5 Series
- SamplerPak
- IntelliDox Docking System
- MicroDock II
- BW Ultra
- BW Solo
- Gas Monitors
- Gas Monitor Manufacturers
- BW Technologies
- Bacharach
- Biosystems
- Crowcon
- Gas Clip Technologies
- GfG Instruments
- GMI/Detcon
- Honeywell Analytics
- Industrial Scientific
- MSA
- RAE Instruments
- RKI Instruments
- Gas Monitor Categories
- Single-Gas Monitors
- Multi-Gas Monitors
- Zero Maintenance Monitors
- Fixed System Gas Monitors
- Confined Space Kits
- Wireless Fixed Point Gas Detectors
- Hydrogen Sulfide (H2S) Monitors
- Calibration Gas
- Combustion Analyzers
- Water Quality
- Reliability Instruments
- Refractometers
- HVAC
- Weather
- Temperature
- Laboratory
- Sound
- IAQ
- Electrical
- All Categories
BW Technologies Rig Rat III Four Channel Controller (for Use with RR-3000 Detectors)
Item #:
RR-3C04
Brand:
BW Technologies
Share this product:
RR-3C04 Rig Rat III Four Channel Controller (for Use with RR-3000 Detectors) by BW Technologies
The Rig Rat III controllers act as the communication center for the Rig Rat III gas detection system. The standard stainless steel Rig Rat III controller allows the simultaneous display of readings and alarm state messages for up to eight remotely located sensors. The system uses a built-in digital 2.4 GHz transceiver, which allows two-way real-time communication with system elements located up to 1.8 miles/3 km away. The controller is in constant communication with detector elements. The detector transmits a discretely coded radio signal to the controller, advising the controller of a gas alarm or integrity alarm conditions.
Packaging Contents:
Rig Rat III Stand-Alone Detectors are equipped with battery back-up, a 5 DBI antenna, local audible/visual alarms, two remote sensor ports, two option ports and a power supply port.Rig Rat III Controllers are equipped with a radio transceiver module, latching audible and/or visual alarms, a discrete option port for alarm bar, a discrete option port for alarm relays, battery back-up, 8 ft./2.5 m plug-in power cable and an antenna port.
Part Number: RR3C04
| CONTROLLERS: | Standard controller (RR-3C04) for up to 4 Rig Rat III detectors |
| Signal Output: | MODBUS (RS-485) -optional |
| Signal Input: | Discretely coded radio signals from each detector |
| Power: | 110 VAC; 230 VAC (selectable) |
| Battery Backup: | Two 12 VDC rechargeable batteries (normal operation: up to 4 hrs.) |
| ALARMS: | |
| Visual: | LCD displays alarm level present, sensor affected and alarm type |
| Audible: | 85 dB at 3 ft. / 1 m (typical) |
| ALARM RELAY OUTPUTS: | Four (4) SPDT relays; 10 amp @ 110 VAC/24 VDC, 8 amp @ 230 VAC |
| INDICATORS: | LEDs (four / channel): 2 alarm indicators, 1 fault, 1 channel enable |
| CONTROLS: | One ON/OFF switch; one ENABLE/DISABLE switch per channel and one momentary reset/test switch |
| PORTS: | |
| Antenna port: | TNC (reverse polarity) |
| Alarm bar port: | 12 VDC output per channel |
| External relay port: | Alarm specific relay option |
| Common relay port: | Low, high and fault (latching configurable) |
| Humidity: | 5% to 95% RH (non-condensing) |
| Enclosure: | Self-contained 14 gauge stainless steel with mounting flanges, NEMA/Type 4 |
| Physical: | 14.95 x 11.16 x 5.15 in. / 37.97 x 28.35 x 13.08 cm; weight 21 lb. / 9.53 kg |
